Worm get gearbox with motor
worm motor
A robust worm-get gearbox powered by an MM28 electric motor. Ideal applications where a simple to match, high torque outcome is required. Ideal for student based projects which includes robots and buggies.
The machine has been designed so that the output shaft could be ‘clicked’ in and out for modification. Electronic.g. reducing to size. The motor is snap installed into its cradle to engage the gear and worm.
Details
1 – 6V DC
0.1A to 1A based on load
Driveshaft length: 12.5cm
Driveshaft diameter 3mm
Gearbox ratio: 42:1
General dimensions of box + motor: 35(W) x 40(H) x 60(L)mm
The primary feature of the high-efficiency gear box is a worm gear, which locks the output shaft whenever the electric motor is not turning. The high gear ratios of 216:1 or 336:1 get this to gearbox appropriate for little strolling robots, lifting mechanisms, and various other applications where large torque is desired.
The low-voltage motors in the worm gearbox run on 1.5-4.5 volts and draft to a few amps, making them ideal candidates for the DRV8833 motor driver carrier. Engine overheating can be due to excessive stalling, even at suprisingly low voltages. We advise that you utilize stall-detection sensors, or just watch your robot, to ensure that it doesn’t stall for more than a few seconds at a time.
This gearbox includes a 4 mm diameter, round output shaft, which works with the wheels that are appropriate for Tamiya 4 mm, round shafts. Our 3 mm universal mounting hub also fits on the smaller threaded end of the shaft, although it is not particularly intended to work with this kind of shaft (the hub’s set screw could damage the thread on the shaft).
Ever-Power gear motors will be economical, right-angle, worm-geared motors that install easily in the tightest applications. Economical right position worm geared motors established new specifications for reliability, efficiency and economy with unparalleled features including hollow shafts in the smallest sizes. An inverter friendly design offers easy integration at this point and a really future proof remedy. The Ever-Power gear motor offers total versatility in mounting options includes shaft, base, face, and flange solutions. The motor terminal box could be mounted in alternative positions rotated in 90º steps around the electric motor frame providing for unparalleled integration possibilities.
Ever-Power gear motors comply with North American and International requirements, including NEMA, IEC, CSA, and CE, the Ever-Power series allows for worldwide acceptance, a true total remedy for our global customers.
Superior protection of IP65 acc. to IEC 529 assures you that the Ever-Power series is dust tight and hose evidence,and can be used outside or in wet and dusty conditions without the use of additional enclosures. Complete rated output is available at the result shaft of the unit.
Product Features
Power ranking up to 5,5 kW.
Torque 25 … 1.000 Nm
Output Speeds 0,2 … 300 min-1
versatile installation possibilities
Completely enclosed, sealed against dust and water spray
Lubrication change first after 15000 hrs
Low noise gearing
Mains connection 110 … 690V, 50/60Hz
Enclosure IP65 (Standard), IP66 (Optional)
Additional features:
Connecting with Plug connectors.
With built-in inverter up to 7,5kW.
Ever-Power-Mark
CSA, UL, ATEX, GOST, CCC, ISO9001, ISO14001, OHSAS18001
Motors according to Sobre 60034
Corrosion category based on DIN ISO 12944-5
C1, C2, C3, C4, C5-We, C5-M
DC WORM GEAR MOTORS
Ever-Power DC worm equipment motors are the option for applications requiring a good corner turn, optional dual output, or perhaps an inability for the electric motor to be back again driven. The DC right angle gear motors are created for constant and intermittent duty operation. Our right angle equipment reducers are designed with many mounting plate choices, making them perfect for a number of DC engine based applications. We offer 12 ratios which range from 5:1 to 100:1.
10309
FEATURES
1/43 to 3/8 HP
12, 24, 90, 130, 180 VDC, 115 FWR
9 – 475 RPM
1.5 – 315.9 in-lb rated torque
Frame Size 60, 80, 108 mm
5:1 – 100:1 standard ratios
Standard brush life of 2000+ hours (varies by application)
EP Products Worm Gear Motors are created to generate high torque in a small package size. Worm Gear Motors are great for applications that require a personal- locking or breaking feature since the result shaft can’t rotate when there’s no power applied. Additionally, Worm Gearheads can transfer movement in 90 degrees. With various reduction ratios, precision minimize gears, voltages and sizes, EP Items has a DC Worm Gear Motor solution for the application.
Features and Benefits
HIGH Torque Capabilities
Self-Locking / Braking Features
Motion Transfer of 90 Degrees
Ability to Handle Large Equipment Reduction Ratios
High Durability
Low Noise
Flexible Configuration
Applications
Security Door Locks / Industrial Conveying Systems / Security Gates / Oral Chairs / Ambulance Cots & Stretchers Quite a few DC Motors could be complimented with one of our Worm Gearheads. EP Items will work with you to design and produce a Worm Gear Motor that may optimize the overall performance of your unique application.
Built to your unique requirements
Motor Type: Brushed / Brushless / Coreless
Voltage
Output Speed
Power
Current
Torque
Reduction Ratio
Shaft Material & Size
Gear Material
Shaft Configuration: (D Trim / Round / Splined / Other)
Overall Size Parameters (L, W, H)
Encoder Type: Optical / Hall Effect
Extra Assembly Requirements (lead wires, connectors, etc.)
INTRODUCTION
The turbo metal gear worm electric motor uses a metal gear box for sturdiness and a higher torque output. Due to the special mechanical framework of the worm drive the engine output shaft is usually self locking and will not be rotated.
This part runs on the two wire connection and supports direction control along with PWM speed control. Ranked voltage is 12v and will achieve 40RPM, with a torque of 8kg/cm.
SPECIFICATION
Operating Voltage: 6 – 15 V
Rated Voltage: 12V
No-load Speed: 40 RPM
No-load Current: 35 mA
Rated Torque: 32 RPM
Rated Current: 180 mA
Rated Torque: 2.2 kg.cm
Rated Power: 1.1 W
Stall Torque: 8 kg/cm
Stall Current: 1 A
Reduction Ratio: 1:150
Weight: 167 g
EP Geared Motors with Worm Gearing – Modual & Customizable drive technology
Worm gear products from EP DRIVESYSTEMS especially display their power in applications where superior gear ratios are essential. Our worm geared motors will be consequently optimally suited for make use of in intralogistics, packaging technology and the food & beverage industry.
Four great reasons for EP worm geared motors:
Rugged
Our worm geared motors have a high overload capacity
Maintenance Friendly
Washdown versions allow simple and effective cleaning of the get system.
Corrosion protection
The NSD tupH sealed surface area conversion is exceptionally chemical, corrosion and abrasion resistant.
Flexibility
Our modular design give users maximum freedom.
The modular system for maximum flexibility: Our EP worm gear units
There are many applications that want drive systems, and each of these has its unique requirements. The EP series worm equipment motors can be quickly and effectively adapted to fulfill your needs.
Worm gear systems impress with their large power density and compact style. If required, we can also supply them with the impressive nsd tupH surface treatment.
As well as the basic EP housing, you can expect an extensive line of bolt-on parts to customize the merchandise including torque arms, shaft addresses and output flanges. These can be easily field set up, but we will also be happy to assemble the individual components for you.
Find out more about our modular SI worm geared motors!
Find out more
Smooth and Clean: The EP worm equipment unit SMI
SMI worm gear systems feature a smooth, corrosion-resistant alluminum alloy housing. Optional nsd tupH surface conversion makes the product preferably suited for harsh and demanding industries like meals processing and pharmaceuticals.
Flexible input designs such as NEMA, IEC or immediate motor mounts in additional foot or flange mounted casing designs.
Worm geared motors
Worm geared motors for little power range.
The WATT small worm gear unit adapt themselves concerning UNIBLOCK design optimally in the geared electric motor program. The units have got on all sides numerous repairing possibilities and enable a simple assembling for the client.
Other drive configurationscan be created by use of built-in accessories (e.g. torque arm and result flanges). The housings are created in light weight structure out of aluminium die cast. Motor attachment is realised generally by way of IEC adapter B5 or B14A.
Technical Data
Number of sizes:5
Power Range:0.12 – 2.2kW
Output torque range:17 – 230Nm
Ratio:5 – 100
Output option:output shaft, result shaft on both sides, hollow shaft, hollow shaft with shrink disc
Assembly/installation:uniblock, flange, torque arm
Buy Worm Drive Gearbox with Electric motor – incorporating the next features: 1 to 6V voltage rating, 17100 rpm no load quickness, 220g-cm stall torque, 3mm shaft size, 60mm long, 35mm vast, 40mm high, a good robust worm drive gearbox powered by an MM28 engine (included), most ideal for applications where an easy to match, high torque output is necessary, nylon housing and equipment, requires light oil or silicon grease lubrication, well suited for student based tasks including robots and buggies.
Most ideal for applications where an easy to fit, high torque end result is required
Ideal for student based projects including robots and buggies
Reversible Excessive torque Turbo Worm Gear Engine JGY370 DC 12V 40RPM
Reversible Great torque Turbo Worm Gear Motor JGY370 DC 12V 40RPM
Features:
The motor is Gear DC engine with micro-turbine worm, you can change the wiring-connection to improve motor rotation.
Turbo worm geared motor with self-lock, that’s, in the case of motor without electrical, the result axis is usually fixed, self-lock.
The reducer output shaft arranged vertically with the electric motor shaft, whole electric motor output shaft relatively-short than general gear electric motor, widely used to be installed the dimensions requirements strictly occasion.
Specifications:
Model: JGY370
Voltage: DC12V
No load speed: 40r/min
Output torque: 5.6kg.cm
Rated current: 0.06A
Weight: 163g
Application: open the windows, door, Mini winch. Ect.
In sumo robot or combat robot competition where large holding torque’s motor is essential in order to avoid your robot being pushed by your opponent robot. The worm equipment is definitely an improved option when compared to spur gear motor. Why is worm gear so particular? Check this wiki out: Worm Drive.
“Unlike with ordinary gear trains, the direction of transmission (insight shaft vs output shaft) isn’t reversible when using large reduction ratios, due to the greater friction involved between the worm and worm-wheel, when usually a single start (one spiral) worm is used. This is normally a advantage when it is desired to eliminate any possibility of the result driving the input.”
In other words, it is challenging to push your load (example, your robot) if the motor isn’t power or rotate.
Features and Spec:
Metal gear box
Output shaft is self-locking because of the worm gear’s characteristic
Rated voltage: 12V DC
Rated output speed: 150 RPM
Rated output torque: 117mN.m (1.2kgf.cm)
Stalled torque: 196mN.m (2kgf.cm)
No load current: 60mA
Stalled current: 1.8A
Output shaft diameter: 6mm with 4.5mm slot
Weight: 150g

Find more articles about worm motor by clicking.