Merchandise Description:
DC motor is a rotating motor that can change DC electric powered strength into mechanical power (DC motor) or mechanical vitality into DC electric powered vitality (DC generator). It is a motor that can transform DC and mechanical power into one another. When it runs as a motor, it is a direct existing motor, which converts electrical strength into mechanical strength when it operates as a generator, it is a direct existing generator, which converts mechanical energy into electrical strength.
| Product Name | One Section Medium Asynchronous DC Motor |
| Motor Sort | DC Motor,ACMotor,Stepper Motor,Asynchronous Motor ,Synchronous Motor (CZPT equipment) |
| Composition structure | The framework of DC motor must consist of two areas: stator and rotor. The static component of DC motor is named stator. The primary operate of stator is to create magnetic field, which is composed of base, major magnetic pole, commutation pole, finish cap, bearing and brush system. Running component is known as rotor, whose main operate is to create electromagnetic torque and inductive electromotive force. It is the hub of energy conversion of DC motor. So it is also typically named armature, which is composed of rotor, armature core, armature winding, commutator and enthusiast. |
| Design | Z Sort |
| Seat amount | Z315-Z1000 |
| energy | 60~2800kW |
| Voltage | 220~1000V |
| Torque assortment | 1.five ~180kNm |
| Protection degree | IP23, IP44 |
| Cooling mode | IC06,IC17,IC37,IC81W |
| Operating pace | Constant Pace /Reduced Pace /Alter Pace /High Speed Other |
| Main classification | DC Motor is a machine that converts mechanical power into DC electrical power. It is largely used as DC motor for DC motor, electrolysis, electroplating, smelting, charging and excitation energy provide of alternator. Even though in areas in which DC electrical power is needed, AC energy rectifier is also utilised to change AC into DC electricity, but from some factors of efficiency, AC rectifier electrical power source can not fully substitute DC generator. |
| Application | DC motors are extensively employed in tape recorders, video clip recorders, movie discs, electric powered shavers, hair dryers, digital watches, toys and so on. |
| Servicing approach | Professional motor upkeep middle motor maintenance procedure: cleaning stator and rotor – changing carbon brush or other elements – vacuum F force dipping paint – drying – Calibration equilibrium. 1. Use environment must be usually dry, motor area must be stored clean, air consumption need to not be hindered by dust, fibers and other obstacles. two. When the thermal safety of the motor carries on to work, it need to be ascertained whether or not the fault will come from the motor or the overload or the location worth of the protecting system is as well reduced. Following removing the fault, it can be set into procedure. 3, make sure that the motor is effectively lubricated during procedure. The general motor runs for about 5000 hours, that is to say, lubricating grease need to be extra or replaced. When bearing overheating or lubricating deterioration is identified in operation, the hydraulic strain ought to change lubricating grease in time. When replacing grease, the aged grease should be taken out, and the oil groove of bearing and bearing protect ought to be washed with gasoline. Then ZL-3 lithium grease must be crammed with one/2 (2 poles) and 2/3 (four poles, 6 poles and 8 poles) of the cavity between the inner and outer rings of the bearing. four. When the daily life of the bearing is over, the vibration and noise of the motor will enhance naturally. When the radial clearance of the bearing reaches the following value, the bearing need to be replaced. 5, when getting rid of the motor, it is Alright to get rid of the rotor from the shaft extension or the non extension end. If it is not required to unload the supporter, it is much more convenient to just take out the rotor from the non-axle extension stop. When pulling out the rotor from the stator, the stator winding or insulation must be prevented from being broken. 6. When changing the windings, the type, dimension, turns and gauges of the first windings need to be recorded. When these knowledge are misplaced, they need to be received from the manufacturer and the unique designed windings ought to be changed at will, which often deteriorates one or numerous overall performance of the motor or even can make it extremely hard to use them. |
